Chase cover replacement around Earleton, FL

Rust streaks or a leak around a metal fireplace? Local pros replace chimney chase covers in Earleton after a free look from our pros.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Chase covers backed by our warranty

Concerned a new cover will rust out like the old one? Our pros fit covers sloped to shed water, fastened securely and sealed right, and the workmanship comes with our warranty.

Your quote lists the cover's metal, its dimensions and how the collar and storm collar were sealed, so there's no question later about what was done. If something isn't right, call and we'll come back to look. It's our 100% satisfaction guarantee at the top of your chimney. The metal chosen and its fasteners are listed too. Reserve a chase cover backed by our warranty in Earleton at (352) 675-6366.

Earleton is on our Alachua County list of places we serve. The Gulf and Atlantic shorelines are away from Earleton.

What's Included

Lid, collars and framing in one visit

Rusted chase covers replaced
Collars sized and placed for each pipe
Listed caps checked and refitted
Fresh covers fitted on chases in Earleton

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Insulation around the pipe

Insulation inside a chase in Earleton can slump against the chimney pipe after years of water from a failing cover, closing the clearance the chimney's listing calls for. Our specialists note any insulation touching the pipe where it can be seen and price correcting it to the listing. Wet insulation is replaced once the leak is stopped. The correction follows the chimney's listing.

How It Works

A cover made to fit your chase

Check lid and box

The cover, collar, storm collar and cap are looked over first, along with the framing beneath.
Measure and order

The chase top is measured on every side, and the cover is made with slope and collars.
Fit and fasten

Soft framing is repaired, and the new cover is set, fastened through the sides and sealed.
Seal and cap

The storm collar is sealed to the maker's instructions and the listed cap goes back on.

Why Choose Us

Covers cut to your chase in Earleton

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

A new lid shouldn't sit on rotten wood, so the framing under the cover gets checked first.

Your written price is freeThe price for the lid, the collar and anything wrong with the box beneath comes on a written quote, free.
Same-day service is availableSame-day visits are available to cover a leaking chase in Earleton until the new top arrives.
Family owned and runA family-owned business that measures twice so your chase cover fits the first time.

Call (352) 675-6366 Get a Free Inspection

Measuring for a custom cover

Chases are framed to suit each house, so their tops come in every size, and they're rarely perfectly square. A cover that fits needs to be made to measure.

Each side of the chase top is measured, then both diagonals; our specialists note where the pipe comes through and how big it is, and record any other vent or pipe passing through.

Those measurements go to the sheet-metal shop, and the cover comes back with its turndown, drip, slope and collar in the right places. It's a second trip, and it's what makes the new cover fit tight on every edge.

How a chase cover rusts through

Rust on a chase cover starts where water stays longest: in low spots on a flat top, along seams, around the collar and at fastener holes. The zinc coating wears there first, then the steel beneath starts to rust.

Once a hole opens, water runs straight into the chase every time it rains, soaking the framing and the insulation around the pipe, and reaching the fireplace below.

Those spots get a close look on every inspection. A cover with surface rust can sometimes be cleaned and coated; one with pitting or holes needs replacing, and a sloped stainless cover stops the cycle.

Covers for chases with several pipes

Two chimney pipes, or a pipe and a vent for another appliance, can share one chase. The cover needs a separate collar for each, and each termination needs room around it.

Where several terminations share a chase, the permitted separation and relative heights need checking for those systems. Their arrangement cannot be selected from another model's drawing. The replacement cover must accommodate the approved layout without obstructing required openings.

Our specialists measure every pipe's position, check the spacing and heights against the maker's guidance, and have the cover made with collars to match. If spacing is off, they'll explain the options. The spacing goes on the quote.

Free Inspection

Checked free before a chase cover is priced

Metal of the cover, rust, holes and low spots that hold water
Collar height, fit and seams around each chimney pipe
Storm collar seating and sealant on the pipe
Measurements taken on site for a made-to-measure replacement cover

Claim 10% off your first service

Your first chase cover from our family business is 10% off when you reserve it today.

Call (352) 675-6366 Get a Free Inspection

FAQs

Ask our pros about chase tops in Earleton

Do you fix rotten wood under the cover?

Our pros repair the framing at the top of the chase so the new cover has solid wood to fasten into. Larger carpentry and siding work is named on the quote with the right trade.

Do you check for animals before sealing the chase?

Yes. Nothing gets sealed in. If an animal is nesting in the chase, our animal removal specialists handle it before the new cover goes on.

Our Services