Chimney flashing repair around Spring Ridge, FL

One free inspection in Spring Ridge covers all four sides of the flashing, the back pan and the attic below.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

The attic tells the story first

Before a stain reaches your ceiling, the attic tends to show it. Dark streaks on the roof boards beside the chimney, wet insulation or rusty nail tips all point to water getting past the flashing above.

Where there's access, the attic side of the chimney is part of every flashing inspection. What our pros see there tells them which side of the chimney to focus on outside and how long the leak has been going on. Wet insulation should be replaced once the leak is fixed, and your quote says who handles it. Ask for a flashing and attic check in Spring Ridge at (352) 675-6366.

Spring Ridge is on our Gilchrist County list of places we serve. When the 2020 Census counted Spring Ridge, it found 442 residents.

What's Included

Every side of the chimney, sealed

Back-side width measured against the cricket rule
Rusted flashing swapped for stainless metal
Joints repointed before new counter flashing
Tile and metal roof details followed to the manual

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Standard metals inland

Standard corrosion-resistant flashing from the maker's stock is a sound choice in Spring Ridge, since salt isn't wearing it away. Stainless still earns its keep by resisting corrosion and staying clear of mortar reactions. Our pros explain the options for your roof and brick and name the metal on the quote, so you know what's going on your chimney. Anything bent is refastened or replaced before the next rain.

Our Process

Attic first, roof line second

Attic and all four sides

The attic below is looked at first, then every side of the flashing on the roof.
Choose reseal or replace

You get each side given a written price, with the reason for the fix we recommend.
Mortar first, then metal

Joints are repointed, base and step pieces fitted, and counter flashing set into the brick.
Seal, show and clean up

Joints are sealed, you see the finished work, and every scrap of old flashing leaves with us.

Why Choose Us

Roof line leaks traced and sealed in Spring Ridge

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

All four sides of the chimney get checked, so the leak isn't just moved from one side to another in Spring Ridge.

Our workmanship warrantyOur workmanship warranty covers the flashing we fit on your chimney in Spring Ridge.
Your written price is freeThe flashing estimate is free and written, side by side for each face of the chimney.
100% satisfaction, guaranteedFlashing we fixed still letting water in? We return. That's our 100% satisfaction guarantee.

Call (352) 675-6366 Get a Free Inspection

The apron across the front

On the downslope face of the chimney, a single apron piece runs across the base, lying over the shingles below and turning up against the brick. Water runs off the chimney face onto it and away down the roof.

It fails at the top edge, where it meets the brick, and at the corners, where it has to wrap around to meet the side pieces. A good apron extends around each corner with a tab so there's no open seam. Our pros check both corners carefully, since a gap there sends water along the side flashing and into the roof deck.

The upslope side takes the most water

Every drop of rain landing on the roof above the chimney runs down to its back face. A narrow chimney can shed that with a back pan, a flashing piece that runs up under the shingles and turns up against the brick, carrying water off to either side.

On a wider chimney, that much water piles up, pushes under the roofing and soaks the brick. Leaves and needles collect there too and hold the water in place. Our specialists check the back pan for rust, splits and debris dams, and tell you if the chimney is wide enough to need a cricket instead.

Following the shingle maker's instructions

On asphalt shingle roofs, the Florida Building Code has chimney flashing applied according to the shingle maker's instructions. Those instructions cover how the base pieces lie under and over the shingle courses and where fasteners may go.

Working to them lets the flashing and the roofing act as one system. It also protects your roof's own warranty, which may depend on the flashing being installed the maker's way. If your shingles are an unusual type, our pros check the maker's details before starting, rather than guessing on the roof. Our pros read those details before cutting any metal, so the pieces lie right the first time.

Free Inspection

A free look at all four sides

Step or continuous flashing along each side of the chimney
Mortar condition along the line where flashing is set
Roofing around the chimney, noted for your roofer if damaged
Chimney width across the slope, measured against the cricket rule

Claim 10% off your first service

Reserve today, and your first flashing repair with our pros carries a 10% discount.

Call (352) 675-6366 Get a Free Inspection

FAQs

Quick answers about chimney flashing

What about the shingles next to the chimney?

Our pros handle the chimney side of the flashing. Shingles, tiles or roof boards that have failed go to a roofer, and we'll coordinate with them and say who does what on the quote.

What happens if the flashing leaks after you fix it?

Our pros come back and put it right, since our workmanship warranty covers the flashing we fit. The quote notes which sides were resealed or replaced, so it's clear what's covered. Book a free flashing inspection in Spring Ridge at (352) 675-6366.

Our Services