Your chimney flashing put right in Starke, FL

Stop the drip at the source. Local chimney flashing repair for homes in Starke, with a free look from our pros first.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Getting a new roof put on

Is a new roof going on your home? That's the ideal moment to redo the chimney flashing too. The base flashing that sits on the roof is tied into the new roofing, and the counter flashing set into the brick has to lap over it properly.

Our pros coordinate with your roofer so the chimney side is ready when they are: mortar joints repaired, counter flashing cut into the brick, and the pieces fitted in the right order. The quote spells out which parts are ours and which are the roofer's. Talk to our flashing specialists before your reroof in Starke: (352) 675-6366.

In our service area, Starke is grouped with Bradford County. According to the 2020 Census, 5,796 people lived in Starke.

What's Included

Every piece of your flashing repair

Rusted flashing swapped for stainless metal
Sealant renewed with masonry-rated products
Chase flashing tucked behind siding and barrier
Exposed nails sealed or the piece replaced

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Sun on the sealant bead

The sealant where counter flashing meets the brick sits in full sun on chimneys in Starke. Over the years, sunlight and heat dry it out, and it starts to crack and pull away at the edges. Our specialists check the bead on every visit and replace it with a masonry-rated sealant before it opens enough to let water behind the flashing.

Our Process

Four sides, one careful repair

Attic and all four sides

The attic below is looked at first, then every side of the flashing on the roof.
Choose reseal or replace

You get each side given a written price, with the reason for the fix we recommend.
Mortar first, then metal

Joints are repointed, base and step pieces fitted, and counter flashing set into the brick.
Seal, show and clean up

Joints are sealed, you see the finished work, and every scrap of old flashing leaves with us.

Why Choose Us

Mortar first, then the metal

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Wherever the brick allows, counter flashing goes into a cut mortar joint instead of relying on caulk alone.

Our workmanship warrantyOur workmanship warranty covers the flashing we fit on your chimney in Starke.
Your written price is freeThe flashing estimate is free and written, side by side for each face of the chimney.
100% satisfaction, guaranteedFlashing we fixed still letting water in? We return. That's our 100% satisfaction guarantee.

Call (352) 675-6366 Get a Free Inspection

Does your chimney need a cricket?

A cricket diverts water approaching the uphill side of a chimney. Whether one is required, and how it connects to the roof, depends on the chimney and roof configuration. The inspection considers those details alongside the flashing instead of assuming every leak needs the same alteration.

Your chimney is measured against that rule, and the measurements go on your quote. A missing cricket on a wide chimney explains a lot of back-side leaks. Building one takes framing, sheathing, flashing and roofing, and your quote says who does that work.

Flashing details on tile roofs

Roofing tile sits higher off the deck than shingles and have curved or flat profiles with gaps underneath. The Florida Building Code points flashing and counterflashing at tile roofs to the tile maker's instructions and the FRSA and TRI tile installation manual.

Those details use flashing shaped or formed to the tile, with a pan under the tiles along the chimney and a flexible or formed piece over them. Our specialists lift and reset tiles carefully to reach the flashing and set aside any that crack for your roofer. The work follows the manual's details from start to finish, with no shingle shortcuts. Tile work takes longer than shingle work, and the quote reflects that.

New roof, new chimney flashing

When a roof is replaced, reusing old chimney flashing is a gamble. The base pieces get bent lifting them out, the old counter flashing may be surface-mounted or rusted, and the new roofing may sit at a different height.

Our pros recommend new flashing with a new roof, timed so the chimney work is ready when the roofer reaches that part. Repointing and reglet cuts happen first, then the base and step pieces go in with the roofing, and the counter flashing goes on last. Getting the order right is half the job. Our specialists can meet your roofer on the roof to agree the sequence before work starts.

Free Inspection

Our free look at the roof line in Starke

The apron across the front of the chimney, including both corners
Overlap of the counter flashing on the base pieces, every side
Sealant beads, their type and whether they've cracked or pulled away
Attic boards, insulation and nail tips next to the chimney

Claim 10% off your first service

Seal the roof line in Starke, and a first repair is 10% off.

Call (352) 675-6366 Get a Free Inspection

FAQs

Common flashing questions in Starke

Is Starke in range for chimney flashing repair?

Of course. Point us to the ceiling or wall that shows the stain, and our pros will check all four sides of the flashing and the attic below at no cost. Starke is part of the Bradford County area we cover.

Can the old flashing just be resealed?

If the metal is sound, lies flat and laps properly, yes, and that's the smaller job. Rusted, short or surface-glued pieces need replacing. Our pros tell you which applies to each side, with both prices where it's close.

Our Services