Your flue lined right in Jonesville, FL

Flue cleaned first, liner fitted, and a walk-through of the first fires in Jonesville. Inspection free.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Relining backed by our warranty

Worried about paying for something you won't see again? The liner runs out of sight inside the chimney, so it's fair to want it covered. Our workmanship warranty covers the installation, and the liner maker's own warranty covers the liner under its terms.

You'll have the liner's make, alloy, size, insulation and listing on your quote, with the date it went in. If anything about the new liner seems off, call and our pros return to check it. Our 100% satisfaction guarantee means the job stays open until you're happy. Reserve relining backed by our warranty in Jonesville by dialing (352) 675-6366.

Jonesville is an inland service location, separate from the sea coast. Jonesville is about 10 miles from the Gainesville reference point, measured in a straight line.

What's Included

Relining work included in Jonesville

Each liner matched to the appliance below it
Tees and cleanout caps at the base
Old aluminum liners checked against the appliance
Break-in steps written out for homeowners in Jonesville

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Two appliances sharing a chimney

If your chimney serves both a fireplace and a furnace or water heater, each should have its own flue, and sometimes, wrongly, they share one. Our specialists check which appliance uses which flue and plan a liner for each that needs one, with two liners side by side where the flue is large enough. Each liner gets its own price. That plan comes on the quote.

How It Works

Relining, one step after another

Read the appliance

The rating plate and manual come first, then the flue is measured and inspected.
Sweep and prove the path

After a sweep, a test piece is run down the flue to confirm the liner will pass.
Wrap, feed and connect

The liner is insulated where needed, fed down, and connected at the bottom.
Seal the top, explain break-in

The top plate and cap go on, the draft is checked, and you get break-in steps.

Why Choose Us

The appliance comes before the liner

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Every flue is proven with a test piece before a liner is ordered.

Your price, upfrontThe liner, insulation and install are priced up front, before anything is ordered for Jonesville.
Our workmanship warrantyThe liner has its maker's warranty, and our workmanship warranty covers how we installed it.
Locally owned and operatedLocally owned, so the liner we install is one we can come back and sweep.

Call (352) 675-6366 Get a Free Inspection

Wrapping the liner in insulation

Selkirk's liner instructions require insulation where the chimney's clearance to combustibles can't be determined, and describe a foil-faced ceramic blanket wrapped with overlapping seams, sealed with foil tape and held with a mesh sleeve.

Our specialists wrap the liner that way before it goes down, checking that the overlap runs the full length. Insulation keeps the flue warmer, which helps the draft and cuts deposit, and it protects the masonry and any framing close to it.

The blanket thickness is the one the liner's listing calls for, and it's named on your quote. Seams face away from where the liner rubs during the feed.

Pouring insulation in around the liner

Some liner makers, National Chimney among them, allow a poured insulation mix around the liner instead of a blanket. It fills the gap around the liner inside the old flue and sets there.

Poured insulation suits flues where a wrapped liner won't fit or where the old tile is too damaged to rely on. It's more work to install and harder to undo, so our pros recommend it only where it's the better answer for your chimney.

You'll see blanket and poured options side by side when both are possible, with the listing each relies on. The mix is the one the liner maker lists.

Listed liner systems

The Florida Building Code accepts listed chimney lining systems, tested to UL 1777, as a flue lining for masonry chimneys. The listing covers the liner, its fittings and the way it's installed, including clearances and insulation.

Liners from our pros go in as complete listed systems, following the maker's instructions for each part, from the top plate and cap to the tee and connector. Mixing parts from different makers, or skipping the insulation the listing calls for, breaks the listing.

The make and listing go on your quote, so future inspectors can see what was installed. That record also helps when you sell the house.

Free Inspection

Rating plate, flue size and offsets, checked free

Type of appliance, its rating plate and its venting instructions
Offsets, ledges and loose tile along the flue
Fireplace opening measured against the flue size rule
Crown and flue top where the liner's top plate will sit

Claim 10% off your first service

Booking your first relining today? Our family business takes 10% off it.

Call (352) 675-6366 Get a Free Inspection

FAQs

Which liner fits your fireplace?

Is Jonesville on your list for relining?

Yes. Our specialists reline chimneys throughout Alachua County, Jonesville included, and every job opens with a free look at the flue and the appliance it serves. Knowing what vents into the chimney helps us come prepared.

Can a liner go through a bent flue?

A flexible stainless liner can pass most offsets. Our specialists prove the path with a test piece first, so you'll know before anything is ordered.

Our Services