Stainless liners fitted in Micanopy, FL

The appliance you burn picks the liner. Local pros size and fit it in Micanopy after a free look at the flue.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Sweeping before the liner goes in

Why sweep a flue you're about to line? Liner makers want the chimney and smoke chamber cleaned before their product is installed. Old deposit left behind a new liner can smolder, and it hides damage that affects the install.

Our specialists sweep the flue and smoke chamber first, then inspect and measure it clean. That's when offsets, loose tile and old damage show up clearly. The sweep has its own price and can happen on the same visit as the measure. Check with one of our local pros about sweeping and relining your chimney in Micanopy at (352) 675-6366.

The sea coast does not form part of Micanopy's boundary. Micanopy is where you'll find Micanopy Historic District.

What's Included

Liner, insulation, connector and top plate

Oval liners sized with enough area
Water heater flues resized after a furnace swap
Liner make and listing recorded for homes in Micanopy
Break-in steps written out for homeowners in Micanopy

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Crowns under inland top plates

The top plate of a relined chimney in Micanopy sits on the crown. A cracked or flat crown lets water in around the plate, down around the liner inside the old flue. Our pros check the crown before fitting the plate and price any repair separately, so the new liner has a sound, dry top. Crown and plate work can happen on one visit.

How It Works

Test piece first, then the full liner in Micanopy

Read the appliance

The rating plate and manual come first, then the flue is measured and inspected.
Sweep and prove the path

After a sweep, a test piece is run down the flue to confirm the liner will pass.
Wrap, feed and connect

The liner is insulated where needed, fed down, and connected at the bottom.
Seal the top, explain break-in

The top plate and cap go on, the draft is checked, and you get break-in steps.

Why Choose Us

Chimney liners sized right in Micanopy

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Flues are swept and cleared before the liner goes in, as liner makers require.

Your price, upfrontThe liner, insulation and install are priced up front, before anything is ordered for Micanopy.
Our workmanship warrantyThe liner has its maker's warranty, and our workmanship warranty covers how we installed it.
Locally owned and operatedLocally owned, so the liner we install is one we can come back and sweep.

Call (352) 675-6366 Get a Free Inspection

Condensation in an oversized flue

Gas exhaust carries water vapor. In a flue that's too large or too cold, the exhaust cools before it leaves, and the water condenses on the flue walls.

That moisture carries acids that eat mortar joints, crack tile and stain the chimney from inside, showing up as white crust and damp patches that look like a rain leak. A liner sized to the appliance keeps the exhaust warm enough to leave as vapor.

Any flue serving a gas appliance is checked for condensation damage, and the new liner is sized to stop it. The appliance's own instructions set the size.

Listed liner systems

The Florida Building Code accepts listed chimney lining systems, tested to UL 1777, as a flue lining for masonry chimneys. The listing covers the liner, its fittings and the way it's installed, including clearances and insulation.

Liners from our pros go in as complete listed systems, following the maker's instructions for each part, from the top plate and cap to the tee and connector. Mixing parts from different makers, or skipping the insulation the listing calls for, breaks the listing.

The make and listing go on your quote, so future inspectors can see what was installed. That record also helps when you sell the house.

Break-in fires on a new liner

Some insulated liner systems call for reduced flue temperatures for a break-in period after installation. National Chimney's instructions, for instance, describe small to moderate fires in a fireplace for the first few hours of use.

The gentler start lets the insulation and joints settle. Our pros give you the break-in steps for your liner spelled out, with what to watch for during those first fires.

After that, the fireplace or insert is used as normal. Skipping the break-in may not cause trouble right away, but it's part of the maker's instructions and worth following. Our pros can answer questions on the phone during those first fires.

Free Inspection

The free relining inspection, flue first

Offsets, ledges and loose tile along the flue
Condition of the clay tile and its joints
Clearances around the chimney that decide whether insulation is needed
Which appliances share which flues in the chimney

Claim 10% off your first service

A sound flue in Micanopy, with a 10% discount on your first service when you book today.

Call (352) 675-6366 Get a Free Inspection

FAQs

Relining, answered in short

What happens to my damper?

For an insert, the damper is removed or fixed open as the insert's instructions say. For an open fireplace, the liner connects above it and the damper stays in use.

Do you run the gas line on a conversion?

No, the gas line is a gas contractor's work. Our specialists handle the liner and venting, and your quote says who handles each part.

Our Services