Newberry chimney relining, sized to the appliance

The appliance you burn picks the liner. Local pros size and fit it in Newberry after a free look at the flue.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Choosing the liner metal

Different jobs call for different stainless alloys. Liner makers such as National Chimney use 316L stainless for wood, pellet, coal, oil and standard gas appliances, and an alloy called AL29-4C for high-efficiency gas appliances whose exhaust is more corrosive.

Aluminum liners exist too, but makers limit them to a narrow class of gas appliances. Our specialists choose the alloy the appliance's instructions and the liner's listing call for, and the metal is written on your quote. The right alloy the first time avoids an early replacement. Reserve a liner in the right alloy for your chimney in Newberry: (352) 675-6366.

In 2020, the Census Bureau counted 7,342 people living in Newberry. The sea coast does not form part of Newberry's boundary.

What's Included

Liner, insulation, connector and top plate

Each liner matched to the appliance below it
Flues proven with a test piece first
Old aluminum liners checked against the appliance
Fire-damaged flues relined

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Selling a home with a relined chimney

Buyers' inspectors in Newberry look for the liner, and a relined chimney with paperwork showing the liner's make, size and listing answers their questions quickly. Our specialists give you that record with every install, along with the date and the insulation used. It also helps the next inspector see what was done, and when, without guessing about the flue. The record stays with the house.

How It Works

Test piece first, then the full liner in Newberry

Read the appliance

The rating plate and manual come first, then the flue is measured and inspected.
Sweep and prove the path

After a sweep, a test piece is run down the flue to confirm the liner will pass.
Wrap, feed and connect

The liner is insulated where needed, fed down, and connected at the bottom.
Seal the top, explain break-in

The top plate and cap go on, the draft is checked, and you get break-in steps.

Why Choose Us

Chimney liners sized right in Newberry

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

The appliance's listing and manual are read first, so the liner in Newberry matches what the appliance was tested with.

Your price, upfrontThe liner, insulation and install are priced up front, before anything is ordered for Newberry.
Our workmanship warrantyThe liner has its maker's warranty, and our workmanship warranty covers how we installed it.
Locally owned and operatedLocally owned, so the liner we install is one we can come back and sweep.

Call (352) 675-6366 Get a Free Inspection

Gas appliance liners, sized by table

Gas furnaces and water heaters are sized for venting by tables in the national fuel gas code, NFPA 54, along with each appliance's own instructions. Those tables weigh the appliance's input, the flue's height and the vent type.

For the same reason, the Florida Building Code points gas flue lining to its own fuel gas rules. Our specialists use those tables and the appliance manuals to pick a liner size, and they check that the liner metal suits the appliance.

An undersized liner can spill exhaust; an oversized one condenses it. Either way, the size chosen, and why, is written on the quote.

Proving the flue before ordering

Proving the flue before installation is something Selkirk's instructions describe: running a test piece or guide cone of the liner's size down the full length to be sure it will pass.

Our specialists run that test on each relining job. Loose tile, mortar ledges, tight joints and offsets show up during the test, and they're cleared or planned for before the liner is ordered. Sometimes the test shows a smaller liner or an oval one is needed.

It's a short step that prevents the worst install-day surprise: a liner stuck halfway down a flue it couldn't have fit. The result is noted on the quote.

A tee fitting at the base of the liner

For some inserts, the liner connects to the appliance through a tee, a T-shaped fitting with a removable cap at its base. Liner makers include it so soot and debris that fall down the liner collect where they can be emptied.

Where the appliance and liner call for a tee, one goes in, and you'll be shown where its cap is. At each sweep the cap is opened and the debris emptied, which keeps the connection from clogging.

Where the setup uses a direct connection instead, you'll hear how that one is checked and cleaned. The cap is easy to reach.

Free Inspection

The free relining inspection, flue first

Fireplace opening measured against the flue size rule
Signs of condensation damage in flues that serve gas appliances
Liner alloy, size, insulation and listing, each priced
Steps for breaking in the liner you choose

Claim 10% off your first service

A new liner, sized and insulated; first-time customers who reserve today claim a 10% discount.

Call (352) 675-6366 Get a Free Inspection

FAQs

Relining, answered in short

Can I use the fireplace right after relining?

Yes, following the break-in steps your liner calls for, such as smaller fires at first. Our pros give you those steps spelled out.

Do you sweep the flue before relining?

Yes. Liner makers require a clean flue and smoke chamber before installation, and a clean flue shows the damage that affects the install. The sweep is priced on its own line.

Our Services