Worthington Springs chimney relining, sized to the appliance

The appliance you burn picks the liner. Local pros size and fit it in Worthington Springs after a free look at the flue.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Chimneys with a bend in the flue

Not every flue runs straight. Some chimneys shift over partway up to clear a roof line or a room, and that offset makes a rigid liner impossible to fit. A flexible liner keeps its full round shape through the bend when it's guided properly.

A corrugated flexible stainless liner bends through offsets while keeping its full diameter. Our pros prove the path with a test piece first, then feed the liner through, guiding it around the bend. If the offset is too sharp for the liner size, they'll tell you before ordering, with the options. Ask about lining a chimney with an offset in Worthington Springs at (352) 675-6366.

Our Worthington Springs coverage is inland from the Gulf and Atlantic coasts. From the Gainesville reference point, Worthington Springs is about 18 miles away in a direct line.

What's Included

Every part of a new liner system

Liners run through offsets without kinking
Old aluminum liners checked against the appliance
Fire-damaged flues relined
Liner make and listing recorded for homes in Worthington Springs

Call (352) 675-6366 Get a Free Inspection

Local Conditions

A liner for a fireplace used now and then

An infrequently used fireplace in Worthington Springs still needs an appropriate liner, connection and termination. A suitable cap helps protect the opening. Whether a top-sealing damper can also be fitted depends on the appliance and fuel, including any requirement to keep the vent permanently open.

How It Works

Relining day in Worthington Springs

Read the appliance

The rating plate and manual come first, then the flue is measured and inspected.
Sweep and prove the path

After a sweep, a test piece is run down the flue to confirm the liner will pass.
Wrap, feed and connect

The liner is insulated where needed, fed down, and connected at the bottom.
Seal the top, explain break-in

The top plate and cap go on, the draft is checked, and you get break-in steps.

Why Choose Us

Flues for inserts, fireplaces and gas appliances

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Flues are swept and cleared before the liner goes in, as liner makers require.

Your price, upfrontThe liner, insulation and install are priced up front, before anything is ordered for Worthington Springs.
Our workmanship warrantyThe liner has its maker's warranty, and our workmanship warranty covers how we installed it.
Locally owned and operatedLocally owned, so the liner we install is one we can come back and sweep.

Call (352) 675-6366 Get a Free Inspection

Why the appliance sets the liner

A liner is part of the appliance's venting system, so the appliance's instructions and listing come first. They name the flue size, sometimes the liner type, and the clearances.

A wood insert might call for a full-length liner of a set diameter. A furnace's instructions point to sizing from the national gas code's venting tables. An open fireplace has its flue size set by the building code in relation to its opening.

Nothing gets measured until the appliance's rating plate and manual are read, so the liner that goes in is the one the appliance was tested with, with no size picked from memory.

Full-length liners for wood inserts

Smoke leaves a wood-burning insert through a collar at the top. Connecting that collar to a full-length liner, running to the top of the chimney, keeps the smoke in a flue sized for the insert instead of spreading into the large clay flue the fireplace had.

The smaller flue stays warmer, drafts better and collects less deposit. Our pros size the liner to the insert's collar and its instructions, fit the connection at the bottom and seal the top.

The insert's manual may also call for insulation on the liner, and that's included where it applies. Everything is priced before the insert goes in.

Cleaning the flue before relining

Liner makers ask for a swept flue and a clean smoke chamber before their product is fitted. Deposit left behind a new liner can keep smoldering, and an unswept flue hides the loose tile and ledges that decide the install.

So the sweep comes first, then the smoke chamber is scraped and anything loose is pulled from the old flue. Then our pros measure and prove the path on a clean flue.

The sweep is part of the relining plan and priced on its own line. If heavy glaze is found, removing it may be a separate step, and you'll hear about it before the liner is ordered.

Free Inspection

Measured and checked before a liner is priced

Damper condition and what the new setup needs
Any existing aluminum liner and whether it still suits
Sweeping needed before the liner can go in
Steps for breaking in the liner you choose

Claim 10% off your first service

A new liner, sized and insulated; first-time customers who reserve today claim a 10% discount.

Call (352) 675-6366 Get a Free Inspection

FAQs

Before relining in Worthington Springs, a few answers

Is Worthington Springs on your list for relining?

Yes. Our specialists reline chimneys throughout Union County, Worthington Springs included, and every job opens with a free look at the flue and the appliance it serves. Knowing what vents into the chimney helps us come prepared.

Is relining covered by a warranty?

You get our workmanship warranty on the installation, and the liner carries its maker's warranty under its terms. Reserve your free relining inspection in Worthington Springs at (352) 675-6366.

Our Services