Chimney masonry repair around LaCrosse, FL

Soft mortar for soft brick, the way the brick industry recommends. Free inspection for chimneys in LaCrosse.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

A bulge in the chimney wall

Noticed a section of the chimney that bows out, even slightly? A bulge means the masonry has come apart inside the wall, with the outer layer separating from what's behind it. It's one to look at soon.

Size, movement and cause, from water in the wall to rusting steel, are the three things to pin down on a bulge. A small bulge can sometimes be taken down and relaid; a large one points to a partial rebuild. Keep people clear of that side until it's assessed. Check with one of our local pros about the bulging section in LaCrosse: (352) 675-6366.

Neither the Gulf nor Atlantic coast reaches LaCrosse. Measured directly, about 11 miles separate LaCrosse from the Gainesville reference point.

What's Included

Mortar, brick and stone repairs in LaCrosse

Stepped cracks traced to their cause and repaired
Loose bricks at the top lifted off and reset
Work covered against rain at the end of each day
Joint profiles tooled to shed water in LaCrosse

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Rain and sun wear masonry in LaCrosse

Away from the coast, chimney masonry in LaCrosse isn't dealing with salt. What wears it is rain soaking into the joints and brick, and the sun heating and drying the wall day after day.

Mortar recesses slowly, and brick faces start to break down where water gets in. Our pros catch that wear early, when repointing a few sections is enough.

Our Process

Repointing your chimney in LaCrosse

Find which half failed

Every face is looked over for worn joints, damaged brick and cracks, and the cause is found.
Match mortar and brick

Samples are mixed and cured, and replacement brick is matched and shown to you.
Joints raked, then refilled

Joints are raked to sound depth, repointed in layers, and damaged brick is swapped out.
Cover, clean, cure

The work is covered against rain, the site cleaned, and you get curing time spelled out.

Why Choose Us

Brick, mortar and stone, done properly

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Local, family-run masonry specialists who explain the cause before the fix in LaCrosse.

100% satisfaction, guaranteedIf the repair doesn't blend in or hold, we make it right. That's our 100% satisfaction guarantee.
Your price, upfrontMasonry work in LaCrosse is priced by section up front, so you can choose what gets done.
Locally owned and operatedA locally owned business, so the masons who repointed your chimney are easy to reach later.

Call (352) 675-6366 Get a Free Inspection

Finding a brick that blends in

A replacement brick has to fit in three ways. It has to be the same size, so the joints around it line up. It has to be similar in how much water it absorbs, so it weathers alongside the bricks around it. And it has to be close in color and texture, so it doesn't stand out.

Salvaged brick is the first place to look, since it has already weathered, and new brick that matches closely comes next. You'll see a sample against the wall in daylight before any cutting starts. When an exact match can't be found, you'll see the closest options and choose.

How thick a chimney wall should be

Masonry chimney walls have a code minimum in Florida: solid masonry units, or hollow units grouted solid, at least 4 inches nominal thickness. That wall is what separates the flue from the rest of the house.

When our specialists repair or relay a section, they keep to that thickness and fill the joints fully, with no voids where heat or water can travel. On a chimney where earlier work left hollow joints or thin spots, they'll point them out. It's one of the checks that separates masonry repair on a chimney from repair on a garden wall. Any hollow joints found are packed full.

When the wall bows out

A section of chimney that bulges outward has separated inside, with the outer brick pulling away from the masonry behind it. Water getting into the wall and rusting ties or steel are common reasons.

Measuring the bulge comes first, then tapping the brick for hollow areas and looking for fresh cracks around the edges that would mean it's still moving. A small, stable bulge can be taken down and relaid with new ties. A large or active one points to rebuilding that section. Until it's assessed, the area below should be kept clear. The repair plan and its price come on the quote once the cause is clear.

Free Inspection

Soft joints and spalled brick, found and priced

Gap or cracking where the chimney meets the house wall
Paint or coatings on the brick and what's under them
Joints on a stone chimney, or veneer checked against the maker's guide
Any bulging sections, tapped by hand to find hollow spots behind the face

Claim 10% off your first service

Your first masonry job with our pros is 10% off.

Call (352) 675-6366 Get a Free Inspection

FAQs

Common masonry questions in LaCrosse

Will the repair match my brick?

Our pros match replacement brick for size, absorption and color, and mix mortar samples to match the old joints. You'll see a sample on the wall before the work starts.

Can you clean the stains off my brick?

Yes, once the water causing them is fixed. Our pros avoid harsh acid cleaners that can burn brick and test gentler methods on a small area first.

Our Services