Chimney masonry repair around Lake Butler, FL

Stair-step cracks, loose top courses or flaking faces? Book a free masonry inspection in Lake Butler today.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

What masonry repair day looks like

Curious how the work goes? Our pros set up ladders or staging, lay tarps over the roof and ground below, and cover anything that could catch dust. Old mortar is raked or ground out to a sound depth.

Fresh mortar is mixed in small batches, packed into the joints in layers and tooled to match. Damaged bricks are cut out and replaced. Each evening the work gets a rain cover and the site gets cleaned. Before they leave, you'll see the finished wall up close. Nothing is left loose on the roof overnight. Reserve your masonry repair in Lake Butler by calling (352) 675-6366.

Lake Butler falls in the Union County part of our service area. The official 2020 count for Lake Butler came to 1,986 residents.

What's Included

Mortar, brick and stone repairs in Lake Butler

Old hard-mortar patches raked out and redone
Loose bricks at the top lifted off and reset
Brick cleaned without harsh acids
Repointing and brick work under our workmanship warranty

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Vines and roots in the joints

Vines climbing a chimney on a home in Lake Butler push their roots into the mortar joints and hold water against the brick. When they're pulled off roughly, they take mortar with them. Our pros remove growth carefully, then repoint the joints underneath. Keeping the chimney clear afterwards lets the brick dry between rains. The joints hidden under the vines tend to need the most care.

Our Process

Repointing your chimney in Lake Butler

Find which half failed

Every face is looked over for worn joints, damaged brick and cracks, and the cause is found.
Match mortar and brick

Samples are mixed and cured, and replacement brick is matched and shown to you.
Joints raked, then refilled

Joints are raked to sound depth, repointed in layers, and damaged brick is swapped out.
Cover, clean, cure

The work is covered against rain, the site cleaned, and you get curing time spelled out.

Why Choose Us

Brick, mortar and stone, done properly

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Work is covered against rain every evening, and the site in Lake Butler is cleaned daily.

100% satisfaction, guaranteedIf the repair doesn't blend in or hold, we make it right. That's our 100% satisfaction guarantee.
Your price, upfrontMasonry work in Lake Butler is priced by section up front, so you can choose what gets done.
Locally owned and operatedA locally owned business, so the masons who repointed your chimney are easy to reach later.

Call (352) 675-6366 Get a Free Inspection

Mortar failure against brick failure

A brick chimney has two materials, and they fail differently. Mortar wears first by design: it softens, recesses and washes out of the joints, while the brick around it stays sound. Brick fails when its face flakes away, when it cracks through, or when it crumbles from years of water.

Each face gets its own note of which material is failing where. The repair follows from that. Worn joints get repointed; damaged brick gets cut out and replaced; walls with both problems get both, in the right order. Getting that diagnosis right is what keeps you from paying for the wrong fix.

How a joint is tooled matters

The shape of a finished mortar joint changes how it handles rain. The Brick Industry Association's guidance on water penetration favors tooled concave and V joints for exterior brick, since tooling compacts the mortar surface and the shape sheds water.

A recessed or struck joint leaves a little shelf where water sits against the brick. On a chimney, where every joint is exposed, that difference adds up. Our pros tool new joints to a water-shedding profile that matches the existing look as closely as possible, and they'll talk it through with you if the old joints were a shape that holds water.

How thick a chimney wall should be

Masonry chimney walls have a code minimum in Florida: solid masonry units, or hollow units grouted solid, at least 4 inches nominal thickness. That wall is what separates the flue from the rest of the house.

When our specialists repair or relay a section, they keep to that thickness and fill the joints fully, with no voids where heat or water can travel. On a chimney where earlier work left hollow joints or thin spots, they'll point them out. It's one of the checks that separates masonry repair on a chimney from repair on a garden wall. Any hollow joints found are packed full.

Free Inspection

Soft joints and spalled brick, found and priced

Mortar joints on every face, and how deep the wear goes
Earlier patches made with hard or mismatched mortar
White and rust staining traced to its source
Paint or coatings on the brick and what's under them

Claim 10% off your first service

Reserve your first brick or mortar repair today and claim 10% off it.

Call (352) 675-6366 Get a Free Inspection

FAQs

Common masonry questions in Lake Butler

Isn't harder mortar better?

Mortar stronger than the brick forces stress into the brick edges and faces, which cracks and flakes them. The Brick Industry Association recommends repointing mortar no stronger than the mortar already in the wall.

Do you repair stone chimneys?

Yes. Natural stone is repointed with a mortar softer than the stone, and manufactured stone veneer is repaired following the maker's installation guide.

Our Services