Sloped, sealed chase tops fitted in Williston Highlands, FL

Measured, made to fit and fastened right by our pros in Williston Highlands, after the free look.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

A chase with more than one pipe

Does your chase hold two chimney pipes, or a chimney and a vent? The cover needs a collar for each pipe, placed where they come through, and the pipes' terminations need room between them.

Makers' instructions call for spacing several terminations apart and staggering their heights, so smoke from one doesn't drift into the other. Our specialists measure every pipe's position and have the cover made with collars to match. Each collar is sized to its pipe with the small gap the maker calls for. Ask our pros about a multi-pipe chase cover in Williston Highlands by dialing (352) 675-6366.

Williston Highlands is on our Levy County list of places we serve. When the 2020 Census counted Williston Highlands, it found 2,591 residents.

What's Included

Lid, collars and framing in one visit

Rusted chase covers replaced
Multi-pipe chases fitted with matching collars
Listed caps checked and refitted
Old covers hauled away from Williston Highlands

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Chases with a vent and a chimney

A chase in Williston Highlands can carry a chimney pipe and a vent for another appliance. Each needs its own collar, and the terminations need spacing between them. Our pros measure both pipes and have the cover made with collars placed to match, checking the spacing against the maker's guidance. Spacing and heights follow the chimney maker's guidance. Each collar is sized to its pipe.

How It Works

A cover made to fit your chase

Check lid and box

The cover, collar, storm collar and cap are looked over first, along with the framing beneath.
Measure and order

The chase top is measured on every side, and the cover is made with slope and collars.
Fit and fasten

Soft framing is repaired, and the new cover is set, fastened through the sides and sealed.
Seal and cap

The storm collar is sealed to the maker's instructions and the listed cap goes back on.

Why Choose Us

Covers cut to your chase in Williston Highlands

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Following the maker's warning, the pipe stays uncaulked at the collar.

Your written price is freeThe price for the lid, the collar and anything wrong with the box beneath comes on a written quote, free.
Same-day service is availableSame-day visits are available to cover a leaking chase in Williston Highlands until the new top arrives.
Family owned and runA family-owned business that measures twice so your chase cover fits the first time.

Call (352) 675-6366 Get a Free Inspection

How a chase cover rusts through

Rust on a chase cover starts where water stays longest: in low spots on a flat top, along seams, around the collar and at fastener holes. The zinc coating wears there first, then the steel beneath starts to rust.

Once a hole opens, water runs straight into the chase every time it rains, soaking the framing and the insulation around the pipe, and reaching the fireplace below.

Those spots get a close look on every inspection. A cover with surface rust can sometimes be cleaned and coated; one with pitting or holes needs replacing, and a sloped stainless cover stops the cycle.

Clearance from the pipe to insulation

Required clearances remain important inside a chase where they are hard to see. Insulation must not occupy an air space the chimney needs. The actual system's instructions determine the separation and shielding, and any uncertainty should be resolved before the chase is closed.

When insulation has been stuffed tight against the pipe, or has slumped against it after getting wet from a leaking cover, that clearance is lost.

Any insulation touching the pipe inside the chase gets noted, along with anything else our specialists can see around it. Correcting it, and replacing insulation soaked by old leaks, is priced separately and done to the chimney's listing. Wet insulation is replaced, since it stays heavy and damp.

Cleaning rust stains off the siding

Every rain carries rust from a failing cover down the chase siding and leaves orange streaks. Once the new cover is on, the source is gone, and the stains stop growing.

Cleaning what's already there depends on the siding. Some cleans up well with a cleaner made for rust stains; some, especially older painted siding, may need repainting to look right.

A small test area comes first, so you know what to expect for your siding. Cleaning is priced separately from the cover, and painting, if needed, goes to a painter. The cleaning method is named on the quote.

Free Inspection

Checked free before a chase cover is priced

Collar height, fit and seams around each chimney pipe
Siding and stains down the sides of the chase
Flashing and water barrier where the chase meets the roof
Fasteners holding the cover and whether they've rusted

Claim 10% off your first service

A rusty lid is worth replacing now, and a first booking knocks 10% off it.

Call (352) 675-6366 Get a Free Inspection

FAQs

Ask our pros about chase tops in Williston Highlands

Can you clean the rust stains off my siding?

In many cases, once the new cover stops the source. Our pros test a small area first, since results depend on the siding. Talk to us about it in Williston Highlands at (352) 675-6366.

Is a chase cover covered by a warranty?

Yes, our workmanship warranty covers the cover we fit, and the quote records its metal, size and how the collar and storm collar were sealed. Reserve your free chase inspection in Williston Highlands at (352) 675-6366.

Our Services