Chimney liner installation around Manatee Road, FL

The appliance you burn picks the liner. Local pros size and fit it in Manatee Road after a free look at the flue.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Adding a wood-burning insert

Planning to put a wood insert into the fireplace? It needs a liner running from its outlet to the top of the chimney, sized to the insert's collar and the maker's instructions. Venting an insert into an oversized clay flue lets smoke cool and deposit build fast.

A stainless liner made for wood, connected to the insert and insulated where the chimney calls for it, fixes that. The liner and the insert installation can be done together so the fireplace goes from open to heating in one project. You'll see each part priced. Talk to our specialists about lining for your insert in Manatee Road at (352) 675-6366.

Our Manatee Road coverage is inland from the Gulf and Atlantic coasts. From the Gainesville reference point, Manatee Road is about 36 miles away in a direct line.

What's Included

Every part of a new liner system

Top plates sealed and caps fitted
Water heater flues resized after a furnace swap
Flues swept before any liner goes in
Old aluminum liners checked against the appliance

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Sun and heat on the top plate

The top plate and its sealant on a chimney in Manatee Road sit in full sun on the crown, and heat from the flue below adds to it. Over the years, the sealant at the plate's edges dries and cracks. Our specialists check that seal on every sweep and reseal it when needed, so water can't run down around the liner inside the old flue.

How It Works

Relining day in Manatee Road

Read the appliance

The rating plate and manual come first, then the flue is measured and inspected.
Sweep and prove the path

After a sweep, a test piece is run down the flue to confirm the liner will pass.
Wrap, feed and connect

The liner is insulated where needed, fed down, and connected at the bottom.
Seal the top, explain break-in

The top plate and cap go on, the draft is checked, and you get break-in steps.

Why Choose Us

Flues for inserts, fireplaces and gas appliances

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Insulation goes on exactly as the liner's listing calls for, named on your quote.

Your price, upfrontThe liner, insulation and install are priced up front, before anything is ordered for Manatee Road.
Our workmanship warrantyThe liner has its maker's warranty, and our workmanship warranty covers how we installed it.
Locally owned and operatedLocally owned, so the liner we install is one we can come back and sweep.

Call (352) 675-6366 Get a Free Inspection

Why the appliance sets the liner

A liner is part of the appliance's venting system, so the appliance's instructions and listing come first. They name the flue size, sometimes the liner type, and the clearances.

A wood insert might call for a full-length liner of a set diameter. A furnace's instructions point to sizing from the national gas code's venting tables. An open fireplace has its flue size set by the building code in relation to its opening.

Nothing gets measured until the appliance's rating plate and manual are read, so the liner that goes in is the one the appliance was tested with, with no size picked from memory.

Where aluminum liners are allowed

Aluminum flexible liners are lighter and cheaper, and they turn up in chimneys serving gas water heaters and furnaces. Their makers limit them: Selkirk's aluminum liner, for instance, is for Category I gas appliances only, and not for solid or liquid fuels or other gas categories.

We check any aluminum liner already in your chimney against the appliance it serves. If the appliance has been changed, or a wood fireplace shares the chimney, the aluminum liner may no longer be suitable.

When they install new, they choose stainless unless the appliance and the maker's rules clearly allow aluminum. The appliance label settles it.

Pouring insulation in around the liner

Some liner makers, National Chimney among them, allow a poured insulation mix around the liner instead of a blanket. It fills the gap around the liner inside the old flue and sets there.

Poured insulation suits flues where a wrapped liner won't fit or where the old tile is too damaged to rely on. It's more work to install and harder to undo, so our pros recommend it only where it's the better answer for your chimney.

You'll see blanket and poured options side by side when both are possible, with the listing each relies on. The mix is the one the liner maker lists.

Free Inspection

Measured and checked before a liner is priced

Condition of the clay tile and its joints
Fireplace opening measured against the flue size rule
Crown and flue top where the liner's top plate will sit
Steps for breaking in the liner you choose

Claim 10% off your first service

A new liner, sized and insulated; first-time customers who reserve today claim a 10% discount.

Call (352) 675-6366 Get a Free Inspection

FAQs

Before relining in Manatee Road, a few answers

Is relining covered by a warranty?

You get our workmanship warranty on the installation, and the liner carries its maker's warranty under its terms. Reserve your free relining inspection in Manatee Road at (352) 675-6366.

Do you sweep the flue before relining?

Yes. Liner makers require a clean flue and smoke chamber before installation, and a clean flue shows the damage that affects the install. The sweep is priced on its own line.

Our Services