Chimney waterproofing around Earleton, FL

A vapor-permeable repellent that keeps liquid water out and lets moisture escape. Free inspection for chimneys in Earleton.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Checking that it's still working

How do you know the repellent is still doing its job? Watch the brick after rain. Water beading and running off means it's working. Brick that darkens and soaks up water evenly means it has worn thin on that face.

On any visit to the chimney, a beading check tells you when a face is due for another coat. Repellents wear faster where the sun and rain hit hardest, so the weather side may need it sooner. Reapplication follows the maker's advice for the product used. Reserve a waterproofing check for your chimney in Earleton by dialing (352) 675-6366.

Earleton falls in the Alachua County part of our service area. Neither the Gulf nor Atlantic coast reaches Earleton.

What's Included

Before and after the repellent goes on

Entry points repaired before any repellent
Efflorescence brushed off before treatment
Old film sealers identified before choosing a product
Crown membranes applied as a separate step

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Gutters that spill onto the brick

Where a gutter spills onto the chimney of a home in Earleton, one section of brick gets soaked every time it rains hard. A repellent can't keep up with that much water pouring over it. Our pros point out any overflow near the chimney. Fixing the gutter comes first; then the soaked section is repaired and tested before any repellent goes on.

Our Process

Coating your chimney in Earleton

Close the gaps

Crown, cap, flashing and joints are repaired first, since a repellent can't seal them.
Test the brick

Absorption is measured on each face and a test patch is checked with you.
Mask and apply

Glass and trim are masked, and the repellent goes on bottom up on dry brick.
Record and recheck

You get the product, faces and date written out, and we check beading on later visits.

Why Choose Us

Waterproofing from a local family business

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Only breathable, penetrating repellents go on chimney brick, with no surface film.

Free inspection firstA brick absorption test is part of the free inspection, so you know if waterproofing is worth it.
No hidden fees, all upfrontNo hidden fees on waterproofing in Earleton; masking, testing and cleanup are in the price.
Family owned and runWe're family owned, and we'll tell you when your chimney doesn't need a coating.

Call (352) 675-6366 Get a Free Inspection

Silanes and siloxanes

Most penetrating masonry repellents are silanes, siloxanes or a blend. The Brick Industry Association describes silanes as smaller molecules that penetrate deeply and need alkaline conditions to react, and siloxanes as larger molecules that bond well with the silica and alumina in brick.

Maker products blend and modify them for particular uses, and chimney repellents are formulated for the heat and moisture a chimney sees. Our specialists choose the product for your brick, test it on a patch, and apply it by the maker's data sheet. The chemistry matters less to you than the result: brick that sheds rain and still breathes.

Why more isn't better

It's tempting to think a heavier coat protects better. The Brick Industry Association notes that over-application can reduce a masonry wall's ability to breathe, which defeats the reason for choosing a penetrating repellent.

Our specialists apply the amount the maker calls for, in the number of coats the data sheet gives, and no more. Extra product can also leave a darkened or glossy look on some brick. If the test patch shows the brick needs a second coat, they'll say so and apply it the way the maker describes. The amount used goes on your quote. That keeps the brick breathing the way it should.

Treating only the faces that need it

Four faces on a chimney means four different doses of weather. The face turned toward the prevailing storms gets the most wind-driven rain and absorbs the most water; a sheltered face may barely get wet.

A repellent is recommended only on faces where the absorption tests high. Treating one or two faces instead of all four saves you money, and it keeps the sheltered faces as breathable as they were. The treated faces are marked on your quote, so you know where to check the beading and what to recoat later. A face treated later can use the same product.

Free Inspection

Tested first, priced second

Absorption of the brick, tested with a tube on each face
Any old sealer, paint or film on the brick surface
Whether the chimney needs a repellent at all
A test patch location on a less visible face

Claim 10% off your first service

Take 10% off your first waterproofing job when you book today.

Call (352) 675-6366 Get a Free Inspection

FAQs

Things to ask before sealing brick in Earleton

How do you know the brick needs it?

Our pros test absorption with a small water tube on each face. Brick that takes in water quickly is a candidate; brick that barely absorbs doesn't need treating.

How will I know when it needs another coat?

Watch the brick after rain. Beading means it's working; brick that darkens and soaks up water means the repellent has worn thin on that face. Our pros check it on every visit.

Our Services