Waterproofing chimneys for homes in Yankeetown

Film sealers trap water; breathable repellents don't. Get a free inspection in Yankeetown and the right product.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Checking that it's still working

How do you know the repellent is still doing its job? Watch the brick after rain. Water beading and running off means it's working. Brick that darkens and soaks up water evenly means it has worn thin on that face.

On any visit to the chimney, a beading check tells you when a face is due for another coat. Repellents wear faster where the sun and rain hit hardest, so the weather side may need it sooner. Reapplication follows the maker's advice for the product used. Reserve a waterproofing check for your chimney in Yankeetown by dialing (352) 675-6366.

Yankeetown recorded a population of 588 in the 2020 Census. Yankeetown reaches the shoreline.

What's Included

What a waterproofing visit covers in Yankeetown

Entry points repaired before any repellent
Breathable repellent applied bottom up
Glass, trim and plants masked and covered
Efflorescence brushed off before treatment

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Salt on the brick before waterproofing in Yankeetown

Salt settles on chimney brick in Yankeetown and works into the surface. A repellent applied over a salty surface can't soak in evenly, and salts trapped under it keep drawing moisture into the brick. Our pros rinse and brush the salt off gently, let the brick dry fully, and test absorption before applying anything. Film sealers are avoided here in particular, since the Brick Industry Association notes salts collect behind low-permeability coatings.

Our Process

Gaps closed before any repellent goes on

Close the gaps

Crown, cap, flashing and joints are repaired first, since a repellent can't seal them.
Test the brick

Absorption is measured on each face and a test patch is checked with you.
Mask and apply

Glass and trim are masked, and the repellent goes on bottom up on dry brick.
Record and recheck

You get the product, faces and date written out, and we check beading on later visits.

Why Choose Us

We test the brick before sealing it

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Each face gets an absorption test before any product is recommended.

Free inspection firstA brick absorption test is part of the free inspection, so you know if waterproofing is worth it.
No hidden fees, all upfrontNo hidden fees on waterproofing in Yankeetown; masking, testing and cleanup are in the price.
Family owned and runWe're family owned, and we'll tell you when your chimney doesn't need a coating.

Call (352) 675-6366 Get a Free Inspection

What film-forming sealers do to brick

Some sealers sit on the surface as a film, such as acrylics, waxes, stearates and urethanes. The Brick Industry Association notes they can bridge hairline cracks but slow evaporation from the wall, and salts can collect under low-permeability coatings.

The question is how a particular coating will behave on this chimney. Ask about its vapor properties, the condition of the wall and any coating already present before agreeing to treatment. A glossy or matt appearance alone cannot answer those questions.

Measuring how thirsty the brick is

A RILEM or Karsten tube is a little marked glass cylinder that gets sealed to the brick face and filled with water. The level drops as the brick absorbs it, and timing that drop gives a simple measure of how much water the face is taking in.

A few spots on each face get tested and compared, and the results decide which faces need a repellent. A face that barely absorbs anything doesn't need treating. Testing again after application shows the repellent is working. It's quick, it's done on the free inspection, and it takes the guesswork out.

Some chimneys don't need waterproofing

According to the Brick Industry Association, a water repellent isn't necessary for brickwork that was properly chosen, detailed, built and maintained, under normal exposure. It also notes that the first round of repairs can solve moisture problems on its own.

Our pros take that seriously. If the crown, cap, flashing and joints are sound and the brick's absorption tests low, they'll recommend skipping the repellent and checking again in a year. You save the cost, and the chimney stays as breathable as it was built to be. If the brick tests high, you'll see the numbers that support treating it. That test result is written on your quote.

Free Inspection

Each face of the brick, tested free

Crown, cap and flashing checked for gaps a repellent can't fix
Absorption of the brick, tested with a tube on each face
Weather side and sheltered faces compared for exposure
A test patch location on a less visible face

Claim 10% off your first service

Damp brick or white bloom? First-time waterproofing is 10% off.

Call (352) 675-6366 Get a Free Inspection

FAQs

Does brick need sealing at all?

Will it change how my brick looks?

A penetrating repellent is meant to leave the brick looking much the same, with water beading on it. Our specialists check a test patch with you before treating the whole chimney.

Does the warranty cover waterproofing?

It covers our application, and the quote records the product, the faces treated and the date. Repellents wear with time and sun, so our pros check the beading on later visits and tell you when a face needs another coat. Reserve a free absorption test in Yankeetown at (352) 675-6366.

Our Services