Gas fireplace installation around Hampton, FL

Installed to the maker's manual, with the gas line run by a gas contractor. Free planning visit for homes in Hampton.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Venting up through the roof

Want the fireplace on an inside wall, or the outside wall won't meet the clearances? The vent can rise up through the ceiling and out the roof instead, as long as the maker's vent table allows the run.

Planning the route through the attic comes first; the vent maker's roof parts go on and the termination is set at the height the manual calls for. The roofing around the new pipe is sealed with the vent maker's roof piece, and where the roof covering itself needs work, your roofer does it, as the quote says. Talk to our specialists about a roof-vented gas fireplace in Hampton by phoning (352) 675-6366.

Neither the Gulf nor Atlantic coast reaches Hampton. Measured directly, about 18 miles separate Hampton from the Gainesville reference point.

What's Included

Gas fireplace installs for homes in Hampton

Units vented straight out through the wall
Roof-vented units with the maker's roof parts
Floors under units prepared as the manual says
Mantel and facing plans checked against the chart

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Insects and nests in a new termination

A termination on a home in Hampton that sits unused for months can attract wasps and nesting birds, which can block the vent. Our specialists ask the vent maker's list about guards for your termination and show you how to check it before the first cool evening of the season. Checking the termination before the season starts takes a minute and saves a service call.

Our Process

Planning a gas install in Hampton

Trace the vent routes

Walls, attic and roof are measured against the vent tables and termination clearances.
Choose and plan

You pick a unit, and the plan covers framing, gas, power and every trade involved.
Install to the manual

The unit is set, the vent assembled and pitched, and the gas contractor connects the line.
First flame and a walkthrough

Leak test, pressures, logs and barrier are checked, and you're shown how to use it.

Why Choose Us

Specialists for direct-vent gas units

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Planning starts with the vent route in Hampton, so the fireplace goes where it can breathe.

Your written price is freeEach unit that fits, with its vent route, is given its own price for free, side by side.
Locally owned and operatedYour installer is locally owned and can service the gas fireplace in Hampton later on.
No hidden fees, all upfrontNo hidden fees: vent parts, framing checks and startup are all on the written price.

Call (352) 675-6366 Get a Free Inspection

Why the vent route comes first

Where a gas fireplace can go depends on where it can vent. The maker's vent tables set how far the pipe can run horizontally for a given vertical rise, how many elbows it can take and where it can end, and those limits decide which walls work.

Every plan starts by tracing the possible vent routes, through the wall behind the unit or up through the ceiling and roof, and checking them against the tables.

Only then do our pros talk about models and finishes. It saves you from falling for a spot on the wall that the vent can't reach.

How a direct-vent unit breathes

Direct-vent gas fireplaces sit sealed off from the room. Every bit of its combustion air comes in from outside, and its exhaust goes back out, through a pipe-within-a-pipe that ends at one termination on the wall or roof.

Because it doesn't use room air, the fuel gas code treats it differently from units that do, and it's the type that can go in more rooms. Its glass front helps close it off.

Our specialists install the vent to the maker's instructions, with every joint locked, so the fresh air and exhaust paths stay separate from end to end. The pipe parts come from the same vent maker.

Fitting the barrier screen

The glass on these units gets hot enough to burn. The 2015 revisions to ANSI Z21.88 and Z21.50 brought in barrier screens for units whose glass exceeds a set temperature, and newer units ship with one that's meant to stay installed.

During installation, the barrier is fitted and checked to sit properly in front of the glass. It's easy to leave off when the finish is going on, and it shouldn't be.

In homes with children or pets, it's one of the most important parts of the whole installation, and it's pointed out at handover. If the screen is ever removed for cleaning, it goes back ahead of your next fire.

Free Inspection

Planned and measured before any price

Walls where a direct-vent unit could vent straight out
Attic and roof route for a vent that goes up instead
Power needs, outlet location and any new circuit
Existing unit and vent when replacing an old fireplace

Claim 10% off your first service

Take 10% off your first gas fireplace service with our family business.

Call (352) 675-6366 Get a Free Inspection

FAQs

What to ask before a gas install in Hampton

Can you install a gas fireplace in Hampton?

Yes, we install gas fireplaces in Hampton and across Bradford County. A free planning visit traces the possible vent routes first. Picture where you'd like the unit before we arrive.

What's the difference between a heater and a decorative unit?

Heaters are listed to ANSI Z21.88 and built to warm the room; decorative units are listed to ANSI Z21.50 and put the look of the flame first. Our pros show you both. Talk to us about which suits you in Hampton at (352) 675-6366.

Our Services