Earleton chimney relining, sized to the appliance

Liners for open fireplaces, wood inserts and gas appliance flues, fitted in Earleton after your free inspection.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

Liner install day at your house

Curious how the liner goes in? After protecting the room and the roof, our pros sweep the flue if needed and clear the path. The liner, wrapped in its insulation if it has any, is fed down from the top with a guide cone leading it.

At the bottom, it's connected to the appliance or the fireplace, and a tee with a cap is fitted where the liner calls for one. At the top, a plate seals the flue opening, the liner is clamped, and a cap goes on. Before leaving, they check the draft and explain the break-in fires. Ask our specialists about install day in Earleton at (352) 675-6366.

From the Gainesville reference point, Earleton is about 16 miles away in a direct line. Earleton is one of the Alachua County places our pros cover.

What's Included

Every part of a new liner system

Top plates sealed and caps fitted
Water heater flues resized after a furnace swap
Wood inserts connected to full-length liners
Liner make and listing recorded for homes in Earleton

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Converting a wood fireplace to gas

Converting a wood fireplace in Earleton to gas? The clay flue that suited wood smoke is far too big for gas exhaust, and condensation follows. Our pros size a liner to the gas appliance's instructions and fit one made for gas exhaust. The gas line is a gas contractor's work, and the quote says who handles it. The liner's alloy is chosen for the gas appliance.

How It Works

Relining day in Earleton

Read the appliance

The rating plate and manual come first, then the flue is measured and inspected.
Sweep and prove the path

After a sweep, a test piece is run down the flue to confirm the liner will pass.
Wrap, feed and connect

The liner is insulated where needed, fed down, and connected at the bottom.
Seal the top, explain break-in

The top plate and cap go on, the draft is checked, and you get break-in steps.

Why Choose Us

Flues for inserts, fireplaces and gas appliances

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Insulation goes on exactly as the liner's listing calls for, named on your quote.

Your price, upfrontThe liner, insulation and install are priced up front, before anything is ordered for Earleton.
Our workmanship warrantyThe liner has its maker's warranty, and our workmanship warranty covers how we installed it.
Locally owned and operatedLocally owned, so the liner we install is one we can come back and sweep.

Call (352) 675-6366 Get a Free Inspection

Gas appliance liners, sized by table

Gas furnaces and water heaters are sized for venting by tables in the national fuel gas code, NFPA 54, along with each appliance's own instructions. Those tables weigh the appliance's input, the flue's height and the vent type.

For the same reason, the Florida Building Code points gas flue lining to its own fuel gas rules. Our specialists use those tables and the appliance manuals to pick a liner size, and they check that the liner metal suits the appliance.

An undersized liner can spill exhaust; an oversized one condenses it. Either way, the size chosen, and why, is written on the quote.

Cleaning the flue before relining

Liner makers ask for a swept flue and a clean smoke chamber before their product is fitted. Deposit left behind a new liner can keep smoldering, and an unswept flue hides the loose tile and ledges that decide the install.

So the sweep comes first, then the smoke chamber is scraped and anything loose is pulled from the old flue. Then our pros measure and prove the path on a clean flue.

The sweep is part of the relining plan and priced on its own line. If heavy glaze is found, removing it may be a separate step, and you'll hear about it before the liner is ordered.

One appliance per flue

Gas appliance makers generally don't allow their vents to connect into a chimney flue serving a wood-burning appliance, and each appliance is meant to have its own flue. Sharing a flue between a fireplace and a furnace can send exhaust where it doesn't belong.

Which appliance uses which flue is the first thing to sort out. Where two appliances share one, our specialists plan separate liners, and in a large enough flue, two liners can run side by side.

Where there's no room for two, you'll hear the options, such as venting one appliance another way, with each priced. Every appliance's flue is labeled on the quote so it's clear which is which.

Free Inspection

Measured and checked before a liner is priced

Condition of the clay tile and its joints
Clearances around the chimney that decide whether insulation is needed
Any existing aluminum liner and whether it still suits
Liner alloy, size, insulation and listing, each priced

Claim 10% off your first service

Relining for the first time with our pros? Arrange a visit and it's 10% off.

Call (352) 675-6366 Get a Free Inspection

FAQs

Before relining in Earleton, a few answers

Does my liner need insulation?

Where the chimney's clearance to combustibles can't be confirmed, liner makers require it, and it also helps the draft. Our pros follow the liner's listing and name the insulation on your quote.

Can a liner go through a bent flue?

A flexible stainless liner can pass most offsets. Our specialists prove the path with a test piece first, so you'll know before anything is ordered.

Our Services