New gas fireplaces fitted in Fairbanks, FL

Want a fire that starts with a switch? Local pros plan the vent, unit and finish in Fairbanks, starting with a free visit.

Family owned and run
Free inspection first
100% satisfaction, guaranteed
Locally owned and operated

Call (352) 675-6366 Get a Free Inspection

Request a Free Inspection

Prefer the phone? Call (352) 675-6366

The first time you light it

Just had the gas fireplace installed? The first burns give off a smell as paints and binders cure. Makers say that's normal, and advise opening windows and running a fan until it passes. One maker recommends a single long first burn with the blower off.

Before we leave, you'll have your unit's break-in steps written out and know how to light it, how the remote works, where the manual override is, and what's normal and what isn't. Call if anything seems off in the first few weeks. Talk to our pros about your new fireplace in Fairbanks by phoning (352) 675-6366.

A straight line from the Gainesville reference point to Fairbanks runs about 6 miles. Fairbanks is on our Alachua County list of places we serve.

What's Included

Vent route, unit, finish and startup

Vent routes checked against the maker's tables
Circuits coordinated with an electrician
Propane units set up or converted with the maker's kit
Startup readings recorded for homes in Fairbanks

Call (352) 675-6366 Get a Free Inspection

Local Conditions

Bedroom fireplaces inland

Want a gas fireplace in a bedroom of your home in Fairbanks? The fuel gas code limits which units can go there, with direct-vent models allowed where their listing permits. Our pros check the room and the listing before recommending a model, and explain the rule on the quote. If the room doesn't qualify, a unit that does is shown instead.

Our Process

Your gas fireplace, from plan to first flame

Trace the vent routes

Walls, attic and roof are measured against the vent tables and termination clearances.
Choose and plan

You pick a unit, and the plan covers framing, gas, power and every trade involved.
Install to the manual

The unit is set, the vent assembled and pitched, and the gas contractor connects the line.
First flame and a walkthrough

Leak test, pressures, logs and barrier are checked, and you're shown how to use it.

Why Choose Us

Gas fireplaces installed to the manual in Fairbanks

Locally owned and run
A family-run company
100% satisfaction guarantee
Your inspection is free
Same-day visits available
Arrange a visit, take 10% off

Local, family-run gas fireplace installers who come back to service what they fit in Fairbanks.

Your written price is freeEach unit that fits, with its vent route, is given its own price for free, side by side.
Locally owned and operatedYour installer is locally owned and can service the gas fireplace in Fairbanks later on.
No hidden fees, all upfrontNo hidden fees: vent parts, framing checks and startup are all on the written price.

Call (352) 675-6366 Get a Free Inspection

Vertical rise and horizontal run

Vent tables tie the pipe's horizontal run to its vertical rise. A longer run needs more rise before it, so the exhaust has the lift to carry it out.

Each elbow counts against the allowed length, and the tables set minimums as well as maximums. A route that falls outside the table can starve the fire of air or push exhaust back.

Our pros sketch the route with its rises, runs and elbows and check it against your unit's table before anything is cut. The sketch goes on your quote, so the installer and you are looking at the same plan.

Height above the ground and walkways

A wall termination can't sit too close to the ground, where plants or debris could block it, or above a walkway where people pass through the exhaust. The manual's clearance table sets minimum heights above grade and above paved walks and driveways.

Ground level and any paths near the proposed spot get measured, and you'll hear about plants that would grow into the clearance zone.

Where a termination sits low enough to be touched, some makers call for a guard, and the manual decides. The final height is on the plan. Plants that would grow into the zone are noted too.

The gas line and its shutoff

A fireplace's gas supply is sized for its input and run to the fuel gas code, with a shutoff valve where the manual shows, so the unit can be isolated for service. That work belongs to a gas contractor.

Planning the fireplace so the connection point is clear, and timing it so the line is ready on installation day, our pros also check with the gas contractor that the supply matches the unit's rating plate.

Once connected, the unit's side is leak-tested and started up to the manual, and each trade's part is named on the quote. Nothing is lit until the connection passes its test.